Svaka ti dala.
Napokon sam poslije dugo ceprkanja nasao isntrukcije koje mogu da pomognu onima sa daljinskim za extra tv sa dugmetom tv/stb
Radi se o sajtu svajcarskog TV provajdera pa gdje god pise Swisscom TV zamislite Extra TV
Originalni text uputstvo: http://www.swisscom.ch/res/hilfe/tv/einrichten/sync/index.htmYou can also use the Swisscom TV remote control to operate your TV. The remote control must be set up once to ensure that it works properly.
If you have acquired a replacement remote control, you can copy the code from your old Swisscom TV remote control. To find out more read the section "Reading out the code from a Swisscom TV remote control which has already been set up".
Method 1: Automatic code search (recommended)
- Switch on your television.
- Press the red button marked "TV-MODE" on your Swisscom TV remote control and hold it in. Keep it pressed in for five seconds until the red LED flashes twice.
- Enter the code 0 0 1. The red LED now flashes twice, indicating that the code has been accepted.
- Point the remote control towards your TV and press the "POWER" button, keeping it pressed in until your TV goes off. Bear in mind that this process may take a few minutes.
- Release the "POWER" button as soon as your TV goes off. Press the "OK" button to save the settings. The red LED flashes twice to confirm this.
- Now switch your TV back on using the Swisscom TV remote control. Now use the remote control to test a few of the functions. If any of the functions do not work properly, repeat steps 1 to 6 until you have found a setting which works correctly.
Method 2: Enter the code (alternative)
- Switch on your television.
- Search through the code list [POGLEDAJ LINK ISPOD]for your make of TV (e.g. Sony). Take note of the codes beside the make markings.
- Press the red button marked "TV-MODE" on your Swisscom TV remote control and hold it in. Keep it pressed in for five seconds until the red LED flashes twice.
- Now enter the first three-digit code shown on the list beside your make of TV.
- The red LED now flashes twice, indicating that the code has been accepted. If you have entered the digits incorrectly, the LED lights up for two seconds. In this case, re-enter the code.
- Now point the remote control towards your TV and press the "POWER" button. Your TV should now go off. If your TV does not go off, repeat steps 2 to 6 with the other codes which are listed for your make of TV.
- Now switch your TV back on using the Swisscom TV remote control. Test a few of the functions with the remote control (channel selection, volume, mute, etc.). If any of the functions do not work properly, repeat steps 1 to 7 with other codes until you have found a setting which works correctly.
Reading out the code from a Swisscom TV remote control which has already been set up
If you have acquired a replacement remote control, it has to be set up once before you can use it for your TV. If you operated your TV using your old Swisscom TV remote control, you can read the correct code from the old remote control.
NB The readout procedure is aborted if you press a button other than 1, 2 or 3, or press none of these buttons for 5 seconds
- Press the TV button on your old Swisscom TV remote control and hold it in until the LED flashes twice.
- To read out the code, now enter code 002 via the number buttons.
- Attention: The first number ("0") must be entered within 5 seconds of the LED flashing twice. If this does not happen, you have to repeat the procedure from point 2.
- Now press "1" and watch out for the flashing signals from the LED. Take note of how often it flashes. If it does not flash, the first number in your code is 0.
- Now press "2" and watch out for the flashing signals from the LED.
- Now press "3" and watch out for the flashing signals from the LED.
- If you make a mistake, you can repeat the procedure as often as you wish.
- Finally, enter the code which you read out here into your replacement remote control applying method 2 (from step 3).
KODOVI: http://www.swisscom-fixnet.ch/FxRes/...inTV_Codes.pdf
Svaka ti dala.
A kako se to poništava?
Tj kako da onda daljinskim od extra tva ponovo upravljam extra tvom? :?
Edit: a vidim.. sa 000
Last edited by institucija; 12-08-11 at 15:45.
jok samo pritisnes TV/STB ponovo prebaci ti na zelenu lampicu i onda opet upravlja sa extra tv
ako nije racun placen, moze li da se i dalje extra tv gleda sa ovim?
Uputstvo i kodovi vec ima na Extra TV temi.
There are currently 1 users browsing this thread. (0 members and 1 guests)
Bookmarks